Files
@ 76497fc594b4
Branch filter:
Location: Jabel/Software/hoverboard-firmware-hack_modified20190825/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_ll_i2c.h
76497fc594b4
62.9 KiB
text/x-chdr
Updated Software repo
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221 1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587 1588 1589 1590 1591 1592 1593 1594 1595 1596 1597 1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 | /**
******************************************************************************
* @file stm32f1xx_ll_i2c.h
* @author MCD Application Team
* @version V1.1.1
* @date 12-May-2017
* @brief Header file of I2C LL module.
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F1xx_LL_I2C_H
#define __STM32F1xx_LL_I2C_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32f1xx.h"
/** @addtogroup STM32F1xx_LL_Driver
* @{
*/
#if defined (I2C1) || defined (I2C2)
/** @defgroup I2C_LL I2C
* @{
*/
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup I2C_LL_Private_Constants I2C Private Constants
* @{
*/
/* Defines used to perform compute and check in the macros */
#define LL_I2C_MAX_SPEED_STANDARD 100000U
#define LL_I2C_MAX_SPEED_FAST 400000U
/**
* @}
*/
/* Private macros ------------------------------------------------------------*/
#if defined(USE_FULL_LL_DRIVER)
/** @defgroup I2C_LL_Private_Macros I2C Private Macros
* @{
*/
/**
* @}
*/
#endif /*USE_FULL_LL_DRIVER*/
/* Exported types ------------------------------------------------------------*/
#if defined(USE_FULL_LL_DRIVER)
/** @defgroup I2C_LL_ES_INIT I2C Exported Init structure
* @{
*/
typedef struct
{
uint32_t PeripheralMode; /*!< Specifies the peripheral mode.
This parameter can be a value of @ref I2C_LL_EC_PERIPHERAL_MODE
This feature can be modified afterwards using unitary function @ref LL_I2C_SetMode(). */
uint32_t ClockSpeed; /*!< Specifies the clock frequency.
This parameter must be set to a value lower than 400kHz (in Hz)
This feature can be modified afterwards using unitary function @ref LL_I2C_SetClockPeriod()
or @ref LL_I2C_SetDutyCycle() or @ref LL_I2C_SetClockSpeedMode() or @ref LL_I2C_ConfigSpeed(). */
uint32_t DutyCycle; /*!< Specifies the I2C fast mode duty cycle.
This parameter can be a value of @ref I2C_LL_EC_DUTYCYCLE
This feature can be modified afterwards using unitary function @ref LL_I2C_SetDutyCycle(). */
uint32_t OwnAddress1; /*!< Specifies the device own address 1.
This parameter must be a value between Min_Data = 0x00 and Max_Data = 0x3FF
This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */
uint32_t TypeAcknowledge; /*!< Specifies the ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte.
This parameter can be a value of @ref I2C_LL_EC_I2C_ACKNOWLEDGE
This feature can be modified afterwards using unitary function @ref LL_I2C_AcknowledgeNextData(). */
uint32_t OwnAddrSize; /*!< Specifies the device own address 1 size (7-bit or 10-bit).
This parameter can be a value of @ref I2C_LL_EC_OWNADDRESS1
This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */
} LL_I2C_InitTypeDef;
/**
* @}
*/
#endif /*USE_FULL_LL_DRIVER*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup I2C_LL_Exported_Constants I2C Exported Constants
* @{
*/
/** @defgroup I2C_LL_EC_GET_FLAG Get Flags Defines
* @brief Flags defines which can be used with LL_I2C_ReadReg function
* @{
*/
#define LL_I2C_SR1_SB I2C_SR1_SB /*!< Start Bit (master mode) */
#define LL_I2C_SR1_ADDR I2C_SR1_ADDR /*!< Address sent (master mode) or
Address matched flag (slave mode) */
#define LL_I2C_SR1_BTF I2C_SR1_BTF /*!< Byte Transfer Finished flag */
#define LL_I2C_SR1_ADD10 I2C_SR1_ADD10 /*!< 10-bit header sent (master mode) */
#define LL_I2C_SR1_STOPF I2C_SR1_STOPF /*!< Stop detection flag (slave mode) */
#define LL_I2C_SR1_RXNE I2C_SR1_RXNE /*!< Data register not empty (receivers) */
#define LL_I2C_SR1_TXE I2C_SR1_TXE /*!< Data register empty (transmitters) */
#define LL_I2C_SR1_BERR I2C_SR1_BERR /*!< Bus error */
#define LL_I2C_SR1_ARLO I2C_SR1_ARLO /*!< Arbitration lost */
#define LL_I2C_SR1_AF I2C_SR1_AF /*!< Acknowledge failure flag */
#define LL_I2C_SR1_OVR I2C_SR1_OVR /*!< Overrun/Underrun */
#define LL_I2C_SR1_PECERR I2C_ISR_PECERR /*!< PEC Error in reception (SMBus mode) */
#define LL_I2C_SR1_TIMEOUT I2C_ISR_TIMEOUT /*!< Timeout detection flag (SMBus mode) */
#define LL_I2C_SR1_SMALERT I2C_ISR_SMALERT /*!< SMBus alert (SMBus mode) */
#define LL_I2C_SR2_MSL I2C_SR2_MSL /*!< Master/Slave flag */
#define LL_I2C_SR2_BUSY I2C_SR2_BUSY /*!< Bus busy flag */
#define LL_I2C_SR2_TRA I2C_SR2_TRA /*!< Transmitter/receiver direction */
#define LL_I2C_SR2_GENCALL I2C_SR2_GENCALL /*!< General call address (Slave mode) */
#define LL_I2C_SR2_SMBDEFAULT I2C_SR2_SMBDEFAULT /*!< SMBus Device default address (Slave mode) */
#define LL_I2C_SR2_SMBHOST I2C_SR2_SMBHOST /*!< SMBus Host address (Slave mode) */
#define LL_I2C_SR2_DUALF I2C_SR2_DUALF /*!< Dual flag (Slave mode) */
/**
* @}
*/
/** @defgroup I2C_LL_EC_IT IT Defines
* @brief IT defines which can be used with LL_I2C_ReadReg and LL_I2C_WriteReg functions
* @{
*/
#define LL_I2C_CR2_ITEVTEN I2C_CR2_ITEVTEN /*!< Events interrupts enable */
#define LL_I2C_CR2_ITBUFEN I2C_CR2_ITBUFEN /*!< Buffer interrupts enable */
#define LL_I2C_CR2_ITERREN I2C_CR2_ITERREN /*!< Error interrupts enable */
/**
* @}
*/
/** @defgroup I2C_LL_EC_OWNADDRESS1 Own Address 1 Length
* @{
*/
#define LL_I2C_OWNADDRESS1_7BIT 0x00004000U /*!< Own address 1 is a 7-bit address. */
#define LL_I2C_OWNADDRESS1_10BIT (uint32_t)(I2C_OAR1_ADDMODE | 0x00004000U) /*!< Own address 1 is a 10-bit address. */
/**
* @}
*/
/** @defgroup I2C_LL_EC_DUTYCYCLE Fast Mode Duty Cycle
* @{
*/
#define LL_I2C_DUTYCYCLE_2 0x00000000U /*!< I2C fast mode Tlow/Thigh = 2 */
#define LL_I2C_DUTYCYCLE_16_9 I2C_CCR_DUTY /*!< I2C fast mode Tlow/Thigh = 16/9 */
/**
* @}
*/
/** @defgroup I2C_LL_EC_CLOCK_SPEED_MODE Master Clock Speed Mode
* @{
*/
#define LL_I2C_CLOCK_SPEED_STANDARD_MODE 0x00000000U /*!< Master clock speed range is standard mode */
#define LL_I2C_CLOCK_SPEED_FAST_MODE I2C_CCR_FS /*!< Master clock speed range is fast mode */
/**
* @}
*/
/** @defgroup I2C_LL_EC_PERIPHERAL_MODE Peripheral Mode
* @{
*/
#define LL_I2C_MODE_I2C 0x00000000U /*!< I2C Master or Slave mode */
#define LL_I2C_MODE_SMBUS_HOST (uint32_t)(I2C_CR1_SMBUS | I2C_CR1_SMBTYPE | I2C_CR1_ENARP) /*!< SMBus Host address acknowledge */
#define LL_I2C_MODE_SMBUS_DEVICE I2C_CR1_SMBUS /*!< SMBus Device default mode (Default address not acknowledge) */
#define LL_I2C_MODE_SMBUS_DEVICE_ARP (uint32_t)(I2C_CR1_SMBUS | I2C_CR1_ENARP) /*!< SMBus Device Default address acknowledge */
/**
* @}
*/
/** @defgroup I2C_LL_EC_I2C_ACKNOWLEDGE Acknowledge Generation
* @{
*/
#define LL_I2C_ACK I2C_CR1_ACK /*!< ACK is sent after current received byte. */
#define LL_I2C_NACK 0x00000000U /*!< NACK is sent after current received byte.*/
/**
* @}
*/
/** @defgroup I2C_LL_EC_DIRECTION Read Write Direction
* @{
*/
#define LL_I2C_DIRECTION_WRITE I2C_SR2_TRA /*!< Bus is in write transfer */
#define LL_I2C_DIRECTION_READ 0x00000000U /*!< Bus is in read transfer */
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup I2C_LL_Exported_Macros I2C Exported Macros
* @{
*/
/** @defgroup I2C_LL_EM_WRITE_READ Common Write and read registers Macros
* @{
*/
/**
* @brief Write a value in I2C register
* @param __INSTANCE__ I2C Instance
* @param __REG__ Register to be written
* @param __VALUE__ Value to be written in the register
* @retval None
*/
#define LL_I2C_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG(__INSTANCE__->__REG__, (__VALUE__))
/**
* @brief Read a value in I2C register
* @param __INSTANCE__ I2C Instance
* @param __REG__ Register to be read
* @retval Register value
*/
#define LL_I2C_ReadReg(__INSTANCE__, __REG__) READ_REG(__INSTANCE__->__REG__)
/**
* @}
*/
/** @defgroup I2C_LL_EM_Exported_Macros_Helper Exported_Macros_Helper
* @{
*/
/**
* @brief Convert Peripheral Clock Frequency in Mhz.
* @param __PCLK__ This parameter must be a value of peripheral clock (in Hz).
* @retval Value of peripheral clock (in Mhz)
*/
#define __LL_I2C_FREQ_HZ_TO_MHZ(__PCLK__) (uint32_t)((__PCLK__)/1000000U)
/**
* @brief Convert Peripheral Clock Frequency in Hz.
* @param __PCLK__ This parameter must be a value of peripheral clock (in Mhz).
* @retval Value of peripheral clock (in Hz)
*/
#define __LL_I2C_FREQ_MHZ_TO_HZ(__PCLK__) (uint32_t)((__PCLK__)*1000000U)
/**
* @brief Compute I2C Clock rising time.
* @param __FREQRANGE__ This parameter must be a value of peripheral clock (in Mhz).
* @param __SPEED__ This parameter must be a value lower than 400kHz (in Hz).
* @retval Value between Min_Data=0x02 and Max_Data=0x3F
*/
#define __LL_I2C_RISE_TIME(__FREQRANGE__, __SPEED__) (uint32_t)(((__SPEED__) <= LL_I2C_MAX_SPEED_STANDARD) ? ((__FREQRANGE__) + 1U) : ((((__FREQRANGE__) * 300U) / 1000U) + 1U))
/**
* @brief Compute Speed clock range to a Clock Control Register (I2C_CCR_CCR) value.
* @param __PCLK__ This parameter must be a value of peripheral clock (in Hz).
* @param __SPEED__ This parameter must be a value lower than 400kHz (in Hz).
* @param __DUTYCYCLE__ This parameter can be one of the following values:
* @arg @ref LL_I2C_DUTYCYCLE_2
* @arg @ref LL_I2C_DUTYCYCLE_16_9
* @retval Value between Min_Data=0x004 and Max_Data=0xFFF, except in FAST DUTY mode where Min_Data=0x001.
*/
#define __LL_I2C_SPEED_TO_CCR(__PCLK__, __SPEED__, __DUTYCYCLE__) (uint32_t)(((__SPEED__) <= LL_I2C_MAX_SPEED_STANDARD)? \
(__LL_I2C_SPEED_STANDARD_TO_CCR((__PCLK__), (__SPEED__))) : \
(__LL_I2C_SPEED_FAST_TO_CCR((__PCLK__), (__SPEED__), (__DUTYCYCLE__))))
/**
* @brief Compute Speed Standard clock range to a Clock Control Register (I2C_CCR_CCR) value.
* @param __PCLK__ This parameter must be a value of peripheral clock (in Hz).
* @param __SPEED__ This parameter must be a value lower than 100kHz (in Hz).
* @retval Value between Min_Data=0x004 and Max_Data=0xFFF.
*/
#define __LL_I2C_SPEED_STANDARD_TO_CCR(__PCLK__, __SPEED__) (uint32_t)(((((__PCLK__)/((__SPEED__) << 1U)) & I2C_CCR_CCR) < 4U)? 4U:((__PCLK__) / ((__SPEED__) << 1U)))
/**
* @brief Compute Speed Fast clock range to a Clock Control Register (I2C_CCR_CCR) value.
* @param __PCLK__ This parameter must be a value of peripheral clock (in Hz).
* @param __SPEED__ This parameter must be a value between Min_Data=100Khz and Max_Data=400Khz (in Hz).
* @param __DUTYCYCLE__ This parameter can be one of the following values:
* @arg @ref LL_I2C_DUTYCYCLE_2
* @arg @ref LL_I2C_DUTYCYCLE_16_9
* @retval Value between Min_Data=0x001 and Max_Data=0xFFF
*/
#define __LL_I2C_SPEED_FAST_TO_CCR(__PCLK__, __SPEED__, __DUTYCYCLE__) (uint32_t)(((__DUTYCYCLE__) == LL_I2C_DUTYCYCLE_2)? \
(((((__PCLK__) / ((__SPEED__) * 3U)) & I2C_CCR_CCR) == 0U)? 1U:((__PCLK__) / ((__SPEED__) * 3U))) : \
(((((__PCLK__) / ((__SPEED__) * 25U)) & I2C_CCR_CCR) == 0U)? 1U:((__PCLK__) / ((__SPEED__) * 25U))))
/**
* @brief Get the Least significant bits of a 10-Bits address.
* @param __ADDRESS__ This parameter must be a value of a 10-Bits slave address.
* @retval Value between Min_Data=0x00 and Max_Data=0xFF
*/
#define __LL_I2C_10BIT_ADDRESS(__ADDRESS__) ((uint8_t)((uint16_t)((__ADDRESS__) & (uint16_t)(0x00FF))))
/**
* @brief Convert a 10-Bits address to a 10-Bits header with Write direction.
* @param __ADDRESS__ This parameter must be a value of a 10-Bits slave address.
* @retval Value between Min_Data=0xF0 and Max_Data=0xF6
*/
#define __LL_I2C_10BIT_HEADER_WRITE(__ADDRESS__) ((uint8_t)((uint16_t)((uint16_t)(((uint16_t)((__ADDRESS__) & (uint16_t)(0x0300))) >> 7) | (uint16_t)(0xF0))))
/**
* @brief Convert a 10-Bits address to a 10-Bits header with Read direction.
* @param __ADDRESS__ This parameter must be a value of a 10-Bits slave address.
* @retval Value between Min_Data=0xF1 and Max_Data=0xF7
*/
#define __LL_I2C_10BIT_HEADER_READ(__ADDRESS__) ((uint8_t)((uint16_t)((uint16_t)(((uint16_t)((__ADDRESS__) & (uint16_t)(0x0300))) >> 7) | (uint16_t)(0xF1))))
/**
* @}
*/
/**
* @}
*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup I2C_LL_Exported_Functions I2C Exported Functions
* @{
*/
/** @defgroup I2C_LL_EF_Configuration Configuration
* @{
*/
/**
* @brief Enable I2C peripheral (PE = 1).
* @rmtoll CR1 PE LL_I2C_Enable
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_Enable(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_PE);
}
/**
* @brief Disable I2C peripheral (PE = 0).
* @rmtoll CR1 PE LL_I2C_Disable
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_Disable(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR1, I2C_CR1_PE);
}
/**
* @brief Check if the I2C peripheral is enabled or disabled.
* @rmtoll CR1 PE LL_I2C_IsEnabled
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabled(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR1, I2C_CR1_PE) == (I2C_CR1_PE));
}
/**
* @brief Enable DMA transmission requests.
* @rmtoll CR2 DMAEN LL_I2C_EnableDMAReq_TX
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableDMAReq_TX(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR2, I2C_CR2_DMAEN);
}
/**
* @brief Disable DMA transmission requests.
* @rmtoll CR2 DMAEN LL_I2C_DisableDMAReq_TX
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableDMAReq_TX(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR2, I2C_CR2_DMAEN);
}
/**
* @brief Check if DMA transmission requests are enabled or disabled.
* @rmtoll CR2 DMAEN LL_I2C_IsEnabledDMAReq_TX
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_TX(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR2, I2C_CR2_DMAEN) == (I2C_CR2_DMAEN));
}
/**
* @brief Enable DMA reception requests.
* @rmtoll CR2 DMAEN LL_I2C_EnableDMAReq_RX
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableDMAReq_RX(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR2, I2C_CR2_DMAEN);
}
/**
* @brief Disable DMA reception requests.
* @rmtoll CR2 DMAEN LL_I2C_DisableDMAReq_RX
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableDMAReq_RX(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR2, I2C_CR2_DMAEN);
}
/**
* @brief Check if DMA reception requests are enabled or disabled.
* @rmtoll CR2 DMAEN LL_I2C_IsEnabledDMAReq_RX
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_RX(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR2, I2C_CR2_DMAEN) == (I2C_CR2_DMAEN));
}
/**
* @brief Get the data register address used for DMA transfer.
* @rmtoll DR DR LL_I2C_DMA_GetRegAddr
* @param I2Cx I2C Instance.
* @retval Address of data register
*/
__STATIC_INLINE uint32_t LL_I2C_DMA_GetRegAddr(I2C_TypeDef *I2Cx)
{
return (uint32_t) & (I2Cx->DR);
}
/**
* @brief Enable Clock stretching.
* @note This bit can only be programmed when the I2C is disabled (PE = 0).
* @rmtoll CR1 NOSTRETCH LL_I2C_EnableClockStretching
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableClockStretching(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH);
}
/**
* @brief Disable Clock stretching.
* @note This bit can only be programmed when the I2C is disabled (PE = 0).
* @rmtoll CR1 NOSTRETCH LL_I2C_DisableClockStretching
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableClockStretching(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH);
}
/**
* @brief Check if Clock stretching is enabled or disabled.
* @rmtoll CR1 NOSTRETCH LL_I2C_IsEnabledClockStretching
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledClockStretching(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH) != (I2C_CR1_NOSTRETCH));
}
/**
* @brief Enable General Call.
* @note When enabled the Address 0x00 is ACKed.
* @rmtoll CR1 ENGC LL_I2C_EnableGeneralCall
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableGeneralCall(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_ENGC);
}
/**
* @brief Disable General Call.
* @note When disabled the Address 0x00 is NACKed.
* @rmtoll CR1 ENGC LL_I2C_DisableGeneralCall
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableGeneralCall(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR1, I2C_CR1_ENGC);
}
/**
* @brief Check if General Call is enabled or disabled.
* @rmtoll CR1 ENGC LL_I2C_IsEnabledGeneralCall
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledGeneralCall(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR1, I2C_CR1_ENGC) == (I2C_CR1_ENGC));
}
/**
* @brief Set the Own Address1.
* @rmtoll OAR1 ADD0 LL_I2C_SetOwnAddress1\n
* OAR1 ADD1_7 LL_I2C_SetOwnAddress1\n
* OAR1 ADD8_9 LL_I2C_SetOwnAddress1\n
* OAR1 ADDMODE LL_I2C_SetOwnAddress1
* @param I2Cx I2C Instance.
* @param OwnAddress1 This parameter must be a value between Min_Data=0 and Max_Data=0x3FF.
* @param OwnAddrSize This parameter can be one of the following values:
* @arg @ref LL_I2C_OWNADDRESS1_7BIT
* @arg @ref LL_I2C_OWNADDRESS1_10BIT
* @retval None
*/
__STATIC_INLINE void LL_I2C_SetOwnAddress1(I2C_TypeDef *I2Cx, uint32_t OwnAddress1, uint32_t OwnAddrSize)
{
MODIFY_REG(I2Cx->OAR1, I2C_OAR1_ADD0 | I2C_OAR1_ADD1_7 | I2C_OAR1_ADD8_9 | I2C_OAR1_ADDMODE, OwnAddress1 | OwnAddrSize);
}
/**
* @brief Set the 7bits Own Address2.
* @note This action has no effect if own address2 is enabled.
* @rmtoll OAR2 ADD2 LL_I2C_SetOwnAddress2
* @param I2Cx I2C Instance.
* @param OwnAddress2 This parameter must be a value between Min_Data=0 and Max_Data=0x7F.
* @retval None
*/
__STATIC_INLINE void LL_I2C_SetOwnAddress2(I2C_TypeDef *I2Cx, uint32_t OwnAddress2)
{
MODIFY_REG(I2Cx->OAR2, I2C_OAR2_ADD2, OwnAddress2);
}
/**
* @brief Enable acknowledge on Own Address2 match address.
* @rmtoll OAR2 ENDUAL LL_I2C_EnableOwnAddress2
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableOwnAddress2(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->OAR2, I2C_OAR2_ENDUAL);
}
/**
* @brief Disable acknowledge on Own Address2 match address.
* @rmtoll OAR2 ENDUAL LL_I2C_DisableOwnAddress2
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableOwnAddress2(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->OAR2, I2C_OAR2_ENDUAL);
}
/**
* @brief Check if Own Address1 acknowledge is enabled or disabled.
* @rmtoll OAR2 ENDUAL LL_I2C_IsEnabledOwnAddress2
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledOwnAddress2(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->OAR2, I2C_OAR2_ENDUAL) == (I2C_OAR2_ENDUAL));
}
/**
* @brief Configure the Peripheral clock frequency.
* @rmtoll CR2 FREQ LL_I2C_SetPeriphClock
* @param I2Cx I2C Instance.
* @param PeriphClock Peripheral Clock (in Hz)
* @retval None
*/
__STATIC_INLINE void LL_I2C_SetPeriphClock(I2C_TypeDef *I2Cx, uint32_t PeriphClock)
{
MODIFY_REG(I2Cx->CR2, I2C_CR2_FREQ, __LL_I2C_FREQ_HZ_TO_MHZ(PeriphClock));
}
/**
* @brief Get the Peripheral clock frequency.
* @rmtoll CR2 FREQ LL_I2C_GetPeriphClock
* @param I2Cx I2C Instance.
* @retval Value of Peripheral Clock (in Hz)
*/
__STATIC_INLINE uint32_t LL_I2C_GetPeriphClock(I2C_TypeDef *I2Cx)
{
return (uint32_t)(__LL_I2C_FREQ_MHZ_TO_HZ(READ_BIT(I2Cx->CR2, I2C_CR2_FREQ)));
}
/**
* @brief Configure the Duty cycle (Fast mode only).
* @rmtoll CCR DUTY LL_I2C_SetDutyCycle
* @param I2Cx I2C Instance.
* @param DutyCycle This parameter can be one of the following values:
* @arg @ref LL_I2C_DUTYCYCLE_2
* @arg @ref LL_I2C_DUTYCYCLE_16_9
* @retval None
*/
__STATIC_INLINE void LL_I2C_SetDutyCycle(I2C_TypeDef *I2Cx, uint32_t DutyCycle)
{
MODIFY_REG(I2Cx->CCR, I2C_CCR_DUTY, DutyCycle);
}
/**
* @brief Get the Duty cycle (Fast mode only).
* @rmtoll CCR DUTY LL_I2C_GetDutyCycle
* @param I2Cx I2C Instance.
* @retval Returned value can be one of the following values:
* @arg @ref LL_I2C_DUTYCYCLE_2
* @arg @ref LL_I2C_DUTYCYCLE_16_9
*/
__STATIC_INLINE uint32_t LL_I2C_GetDutyCycle(I2C_TypeDef *I2Cx)
{
return (uint32_t)(READ_BIT(I2Cx->CCR, I2C_CCR_DUTY));
}
/**
* @brief Configure the I2C master clock speed mode.
* @rmtoll CCR FS LL_I2C_SetClockSpeedMode
* @param I2Cx I2C Instance.
* @param ClockSpeedMode This parameter can be one of the following values:
* @arg @ref LL_I2C_CLOCK_SPEED_STANDARD_MODE
* @arg @ref LL_I2C_CLOCK_SPEED_FAST_MODE
* @retval None
*/
__STATIC_INLINE void LL_I2C_SetClockSpeedMode(I2C_TypeDef *I2Cx, uint32_t ClockSpeedMode)
{
MODIFY_REG(I2Cx->CCR, I2C_CCR_FS, ClockSpeedMode);
}
/**
* @brief Get the the I2C master speed mode.
* @rmtoll CCR FS LL_I2C_GetClockSpeedMode
* @param I2Cx I2C Instance.
* @retval Returned value can be one of the following values:
* @arg @ref LL_I2C_CLOCK_SPEED_STANDARD_MODE
* @arg @ref LL_I2C_CLOCK_SPEED_FAST_MODE
*/
__STATIC_INLINE uint32_t LL_I2C_GetClockSpeedMode(I2C_TypeDef *I2Cx)
{
return (uint32_t)(READ_BIT(I2Cx->CCR, I2C_CCR_FS));
}
/**
* @brief Configure the SCL, SDA rising time.
* @note This bit can only be programmed when the I2C is disabled (PE = 0).
* @rmtoll TRISE TRISE LL_I2C_SetRiseTime
* @param I2Cx I2C Instance.
* @param RiseTime This parameter must be a value between Min_Data=0x02 and Max_Data=0x3F.
* @retval None
*/
__STATIC_INLINE void LL_I2C_SetRiseTime(I2C_TypeDef *I2Cx, uint32_t RiseTime)
{
MODIFY_REG(I2Cx->TRISE, I2C_TRISE_TRISE, RiseTime);
}
/**
* @brief Get the SCL, SDA rising time.
* @rmtoll TRISE TRISE LL_I2C_GetRiseTime
* @param I2Cx I2C Instance.
* @retval Value between Min_Data=0x02 and Max_Data=0x3F
*/
__STATIC_INLINE uint32_t LL_I2C_GetRiseTime(I2C_TypeDef *I2Cx)
{
return (uint32_t)(READ_BIT(I2Cx->TRISE, I2C_TRISE_TRISE));
}
/**
* @brief Configure the SCL high and low period.
* @note This bit can only be programmed when the I2C is disabled (PE = 0).
* @rmtoll CCR CCR LL_I2C_SetClockPeriod
* @param I2Cx I2C Instance.
* @param ClockPeriod This parameter must be a value between Min_Data=0x004 and Max_Data=0xFFF, except in FAST DUTY mode where Min_Data=0x001.
* @retval None
*/
__STATIC_INLINE void LL_I2C_SetClockPeriod(I2C_TypeDef *I2Cx, uint32_t ClockPeriod)
{
MODIFY_REG(I2Cx->CCR, I2C_CCR_CCR, ClockPeriod);
}
/**
* @brief Get the SCL high and low period.
* @rmtoll CCR CCR LL_I2C_GetClockPeriod
* @param I2Cx I2C Instance.
* @retval Value between Min_Data=0x004 and Max_Data=0xFFF, except in FAST DUTY mode where Min_Data=0x001.
*/
__STATIC_INLINE uint32_t LL_I2C_GetClockPeriod(I2C_TypeDef *I2Cx)
{
return (uint32_t)(READ_BIT(I2Cx->CCR, I2C_CCR_CCR));
}
/**
* @brief Configure the SCL speed.
* @note This bit can only be programmed when the I2C is disabled (PE = 0).
* @rmtoll CR2 FREQ LL_I2C_ConfigSpeed\n
* TRISE TRISE LL_I2C_ConfigSpeed\n
* CCR FS LL_I2C_ConfigSpeed\n
* CCR DUTY LL_I2C_ConfigSpeed\n
* CCR CCR LL_I2C_ConfigSpeed
* @param I2Cx I2C Instance.
* @param PeriphClock Peripheral Clock (in Hz)
* @param ClockSpeed This parameter must be a value lower than 400kHz (in Hz).
* @param DutyCycle This parameter can be one of the following values:
* @arg @ref LL_I2C_DUTYCYCLE_2
* @arg @ref LL_I2C_DUTYCYCLE_16_9
* @retval None
*/
__STATIC_INLINE void LL_I2C_ConfigSpeed(I2C_TypeDef *I2Cx, uint32_t PeriphClock, uint32_t ClockSpeed,
uint32_t DutyCycle)
{
register uint32_t freqrange = 0x0U;
register uint32_t clockconfig = 0x0U;
/* Compute frequency range */
freqrange = __LL_I2C_FREQ_HZ_TO_MHZ(PeriphClock);
/* Configure I2Cx: Frequency range register */
MODIFY_REG(I2Cx->CR2, I2C_CR2_FREQ, freqrange);
/* Configure I2Cx: Rise Time register */
MODIFY_REG(I2Cx->TRISE, I2C_TRISE_TRISE, __LL_I2C_RISE_TIME(freqrange, ClockSpeed));
/* Configure Speed mode, Duty Cycle and Clock control register value */
if (ClockSpeed > LL_I2C_MAX_SPEED_STANDARD)
{
/* Set Speed mode at fast and duty cycle for Clock Speed request in fast clock range */
clockconfig = LL_I2C_CLOCK_SPEED_FAST_MODE | \
__LL_I2C_SPEED_FAST_TO_CCR(PeriphClock, ClockSpeed, DutyCycle) | \
DutyCycle;
}
else
{
/* Set Speed mode at standard for Clock Speed request in standard clock range */
clockconfig = LL_I2C_CLOCK_SPEED_STANDARD_MODE | \
__LL_I2C_SPEED_STANDARD_TO_CCR(PeriphClock, ClockSpeed);
}
/* Configure I2Cx: Clock control register */
MODIFY_REG(I2Cx->CCR, (I2C_CCR_FS | I2C_CCR_DUTY | I2C_CCR_CCR), clockconfig);
}
/**
* @brief Configure peripheral mode.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 SMBUS LL_I2C_SetMode\n
* CR1 SMBTYPE LL_I2C_SetMode\n
* CR1 ENARP LL_I2C_SetMode
* @param I2Cx I2C Instance.
* @param PeripheralMode This parameter can be one of the following values:
* @arg @ref LL_I2C_MODE_I2C
* @arg @ref LL_I2C_MODE_SMBUS_HOST
* @arg @ref LL_I2C_MODE_SMBUS_DEVICE
* @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP
* @retval None
*/
__STATIC_INLINE void LL_I2C_SetMode(I2C_TypeDef *I2Cx, uint32_t PeripheralMode)
{
MODIFY_REG(I2Cx->CR1, I2C_CR1_SMBUS | I2C_CR1_SMBTYPE | I2C_CR1_ENARP, PeripheralMode);
}
/**
* @brief Get peripheral mode.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 SMBUS LL_I2C_GetMode\n
* CR1 SMBTYPE LL_I2C_GetMode\n
* CR1 ENARP LL_I2C_GetMode
* @param I2Cx I2C Instance.
* @retval Returned value can be one of the following values:
* @arg @ref LL_I2C_MODE_I2C
* @arg @ref LL_I2C_MODE_SMBUS_HOST
* @arg @ref LL_I2C_MODE_SMBUS_DEVICE
* @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP
*/
__STATIC_INLINE uint32_t LL_I2C_GetMode(I2C_TypeDef *I2Cx)
{
return (uint32_t)(READ_BIT(I2Cx->CR1, I2C_CR1_SMBUS | I2C_CR1_SMBTYPE | I2C_CR1_ENARP));
}
/**
* @brief Enable SMBus alert (Host or Device mode)
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note SMBus Device mode:
* - SMBus Alert pin is drived low and
* Alert Response Address Header acknowledge is enabled.
* SMBus Host mode:
* - SMBus Alert pin management is supported.
* @rmtoll CR1 ALERT LL_I2C_EnableSMBusAlert
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableSMBusAlert(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_ALERT);
}
/**
* @brief Disable SMBus alert (Host or Device mode)
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note SMBus Device mode:
* - SMBus Alert pin is not drived (can be used as a standard GPIO) and
* Alert Response Address Header acknowledge is disabled.
* SMBus Host mode:
* - SMBus Alert pin management is not supported.
* @rmtoll CR1 ALERT LL_I2C_DisableSMBusAlert
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableSMBusAlert(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR1, I2C_CR1_ALERT);
}
/**
* @brief Check if SMBus alert (Host or Device mode) is enabled or disabled.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 ALERT LL_I2C_IsEnabledSMBusAlert
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusAlert(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR1, I2C_CR1_ALERT) == (I2C_CR1_ALERT));
}
/**
* @brief Enable SMBus Packet Error Calculation (PEC).
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 ENPEC LL_I2C_EnableSMBusPEC
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableSMBusPEC(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_ENPEC);
}
/**
* @brief Disable SMBus Packet Error Calculation (PEC).
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 ENPEC LL_I2C_DisableSMBusPEC
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableSMBusPEC(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR1, I2C_CR1_ENPEC);
}
/**
* @brief Check if SMBus Packet Error Calculation (PEC) is enabled or disabled.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 ENPEC LL_I2C_IsEnabledSMBusPEC
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPEC(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR1, I2C_CR1_ENPEC) == (I2C_CR1_ENPEC));
}
/**
* @}
*/
/** @defgroup I2C_LL_EF_IT_Management IT_Management
* @{
*/
/**
* @brief Enable TXE interrupt.
* @rmtoll CR2 ITEVTEN LL_I2C_EnableIT_TX\n
* CR2 ITBUFEN LL_I2C_EnableIT_TX
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableIT_TX(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN);
}
/**
* @brief Disable TXE interrupt.
* @rmtoll CR2 ITEVTEN LL_I2C_DisableIT_TX\n
* CR2 ITBUFEN LL_I2C_DisableIT_TX
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableIT_TX(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN);
}
/**
* @brief Check if the TXE Interrupt is enabled or disabled.
* @rmtoll CR2 ITEVTEN LL_I2C_IsEnabledIT_TX\n
* CR2 ITBUFEN LL_I2C_IsEnabledIT_TX
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_TX(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN) == (I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN));
}
/**
* @brief Enable RXNE interrupt.
* @rmtoll CR2 ITEVTEN LL_I2C_EnableIT_RX\n
* CR2 ITBUFEN LL_I2C_EnableIT_RX
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableIT_RX(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN);
}
/**
* @brief Disable RXNE interrupt.
* @rmtoll CR2 ITEVTEN LL_I2C_DisableIT_RX\n
* CR2 ITBUFEN LL_I2C_DisableIT_RX
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableIT_RX(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN);
}
/**
* @brief Check if the RXNE Interrupt is enabled or disabled.
* @rmtoll CR2 ITEVTEN LL_I2C_IsEnabledIT_RX\n
* CR2 ITBUFEN LL_I2C_IsEnabledIT_RX
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_RX(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN) == (I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN));
}
/**
* @brief Enable Events interrupts.
* @note Any of these events will generate interrupt :
* Start Bit (SB)
* Address sent, Address matched (ADDR)
* 10-bit header sent (ADD10)
* Stop detection (STOPF)
* Byte transfer finished (BTF)
*
* @note Any of these events will generate interrupt if Buffer interrupts are enabled too(using unitary function @ref LL_I2C_EnableIT_BUF()) :
* Receive buffer not empty (RXNE)
* Transmit buffer empty (TXE)
* @rmtoll CR2 ITEVTEN LL_I2C_EnableIT_EVT
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableIT_EVT(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN);
}
/**
* @brief Disable Events interrupts.
* @note Any of these events will generate interrupt :
* Start Bit (SB)
* Address sent, Address matched (ADDR)
* 10-bit header sent (ADD10)
* Stop detection (STOPF)
* Byte transfer finished (BTF)
* Receive buffer not empty (RXNE)
* Transmit buffer empty (TXE)
* @rmtoll CR2 ITEVTEN LL_I2C_DisableIT_EVT
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableIT_EVT(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN);
}
/**
* @brief Check if Events interrupts are enabled or disabled.
* @rmtoll CR2 ITEVTEN LL_I2C_IsEnabledIT_EVT
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_EVT(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN) == (I2C_CR2_ITEVTEN));
}
/**
* @brief Enable Buffer interrupts.
* @note Any of these Buffer events will generate interrupt if Events interrupts are enabled too(using unitary function @ref LL_I2C_EnableIT_EVT()) :
* Receive buffer not empty (RXNE)
* Transmit buffer empty (TXE)
* @rmtoll CR2 ITBUFEN LL_I2C_EnableIT_BUF
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableIT_BUF(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR2, I2C_CR2_ITBUFEN);
}
/**
* @brief Disable Buffer interrupts.
* @note Any of these Buffer events will generate interrupt :
* Receive buffer not empty (RXNE)
* Transmit buffer empty (TXE)
* @rmtoll CR2 ITBUFEN LL_I2C_DisableIT_BUF
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableIT_BUF(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITBUFEN);
}
/**
* @brief Check if Buffer interrupts are enabled or disabled.
* @rmtoll CR2 ITBUFEN LL_I2C_IsEnabledIT_BUF
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_BUF(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR2, I2C_CR2_ITBUFEN) == (I2C_CR2_ITBUFEN));
}
/**
* @brief Enable Error interrupts.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note Any of these errors will generate interrupt :
* Bus Error detection (BERR)
* Arbitration Loss (ARLO)
* Acknowledge Failure(AF)
* Overrun/Underrun (OVR)
* SMBus Timeout detection (TIMEOUT)
* SMBus PEC error detection (PECERR)
* SMBus Alert pin event detection (SMBALERT)
* @rmtoll CR2 ITERREN LL_I2C_EnableIT_ERR
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableIT_ERR(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR2, I2C_CR2_ITERREN);
}
/**
* @brief Disable Error interrupts.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note Any of these errors will generate interrupt :
* Bus Error detection (BERR)
* Arbitration Loss (ARLO)
* Acknowledge Failure(AF)
* Overrun/Underrun (OVR)
* SMBus Timeout detection (TIMEOUT)
* SMBus PEC error detection (PECERR)
* SMBus Alert pin event detection (SMBALERT)
* @rmtoll CR2 ITERREN LL_I2C_DisableIT_ERR
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableIT_ERR(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITERREN);
}
/**
* @brief Check if Error interrupts are enabled or disabled.
* @rmtoll CR2 ITERREN LL_I2C_IsEnabledIT_ERR
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_ERR(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR2, I2C_CR2_ITERREN) == (I2C_CR2_ITERREN));
}
/**
* @}
*/
/** @defgroup I2C_LL_EF_FLAG_management FLAG_management
* @{
*/
/**
* @brief Indicate the status of Transmit data register empty flag.
* @note RESET: When next data is written in Transmit data register.
* SET: When Transmit data register is empty.
* @rmtoll SR1 TXE LL_I2C_IsActiveFlag_TXE
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TXE(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_TXE) == (I2C_SR1_TXE));
}
/**
* @brief Indicate the status of Byte Transfer Finished flag.
* RESET: When Data byte transfer not done.
* SET: When Data byte transfer succeeded.
* @rmtoll SR1 BTF LL_I2C_IsActiveFlag_BTF
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BTF(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_BTF) == (I2C_SR1_BTF));
}
/**
* @brief Indicate the status of Receive data register not empty flag.
* @note RESET: When Receive data register is read.
* SET: When the received data is copied in Receive data register.
* @rmtoll SR1 RXNE LL_I2C_IsActiveFlag_RXNE
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_RXNE(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_RXNE) == (I2C_SR1_RXNE));
}
/**
* @brief Indicate the status of Start Bit (master mode).
* @note RESET: When No Start condition.
* SET: When Start condition is generated.
* @rmtoll SR1 SB LL_I2C_IsActiveFlag_SB
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_SB(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_SB) == (I2C_SR1_SB));
}
/**
* @brief Indicate the status of Address sent (master mode) or Address matched flag (slave mode).
* @note RESET: Clear default value.
* SET: When the address is fully sent (master mode) or when the received slave address matched with one of the enabled slave address (slave mode).
* @rmtoll SR1 ADDR LL_I2C_IsActiveFlag_ADDR
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ADDR(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_ADDR) == (I2C_SR1_ADDR));
}
/**
* @brief Indicate the status of 10-bit header sent (master mode).
* @note RESET: When no ADD10 event occured.
* SET: When the master has sent the first address byte (header).
* @rmtoll SR1 ADD10 LL_I2C_IsActiveFlag_ADD10
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ADD10(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_ADD10) == (I2C_SR1_ADD10));
}
/**
* @brief Indicate the status of Acknowledge failure flag.
* @note RESET: No acknowledge failure.
* SET: When an acknowledge failure is received after a byte transmission.
* @rmtoll SR1 AF LL_I2C_IsActiveFlag_AF
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_AF(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_AF) == (I2C_SR1_AF));
}
/**
* @brief Indicate the status of Stop detection flag (slave mode).
* @note RESET: Clear default value.
* SET: When a Stop condition is detected.
* @rmtoll SR1 STOPF LL_I2C_IsActiveFlag_STOP
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_STOP(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_STOPF) == (I2C_SR1_STOPF));
}
/**
* @brief Indicate the status of Bus error flag.
* @note RESET: Clear default value.
* SET: When a misplaced Start or Stop condition is detected.
* @rmtoll SR1 BERR LL_I2C_IsActiveFlag_BERR
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BERR(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_BERR) == (I2C_SR1_BERR));
}
/**
* @brief Indicate the status of Arbitration lost flag.
* @note RESET: Clear default value.
* SET: When arbitration lost.
* @rmtoll SR1 ARLO LL_I2C_IsActiveFlag_ARLO
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ARLO(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_ARLO) == (I2C_SR1_ARLO));
}
/**
* @brief Indicate the status of Overrun/Underrun flag.
* @note RESET: Clear default value.
* SET: When an overrun/underrun error occurs (Clock Stretching Disabled).
* @rmtoll SR1 OVR LL_I2C_IsActiveFlag_OVR
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_OVR(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_OVR) == (I2C_SR1_OVR));
}
/**
* @brief Indicate the status of SMBus PEC error flag in reception.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll SR1 PECERR LL_I2C_IsActiveSMBusFlag_PECERR
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_PECERR(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_PECERR) == (I2C_SR1_PECERR));
}
/**
* @brief Indicate the status of SMBus Timeout detection flag.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll SR1 TIMEOUT LL_I2C_IsActiveSMBusFlag_TIMEOUT
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_TIMEOUT(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_TIMEOUT) == (I2C_SR1_TIMEOUT));
}
/**
* @brief Indicate the status of SMBus alert flag.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll SR1 SMBALERT LL_I2C_IsActiveSMBusFlag_ALERT
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_ALERT(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR1, I2C_SR1_SMBALERT) == (I2C_SR1_SMBALERT));
}
/**
* @brief Indicate the status of Bus Busy flag.
* @note RESET: Clear default value.
* SET: When a Start condition is detected.
* @rmtoll SR2 BUSY LL_I2C_IsActiveFlag_BUSY
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BUSY(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR2, I2C_SR2_BUSY) == (I2C_SR2_BUSY));
}
/**
* @brief Indicate the status of Dual flag.
* @note RESET: Received address matched with OAR1.
* SET: Received address matched with OAR2.
* @rmtoll SR2 DUALF LL_I2C_IsActiveFlag_DUAL
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_DUAL(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR2, I2C_SR2_DUALF) == (I2C_SR2_DUALF));
}
/**
* @brief Indicate the status of SMBus Host address reception (Slave mode).
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note RESET: No SMBus Host address
* SET: SMBus Host address received.
* @note This status is cleared by hardware after a STOP condition or repeated START condition.
* @rmtoll SR2 SMBHOST LL_I2C_IsActiveSMBusFlag_SMBHOST
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_SMBHOST(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR2, I2C_SR2_SMBHOST) == (I2C_SR2_SMBHOST));
}
/**
* @brief Indicate the status of SMBus Device default address reception (Slave mode).
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note RESET: No SMBus Device default address
* SET: SMBus Device default address received.
* @note This status is cleared by hardware after a STOP condition or repeated START condition.
* @rmtoll SR2 SMBDEFAULT LL_I2C_IsActiveSMBusFlag_SMBDEFAULT
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_SMBDEFAULT(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR2, I2C_SR2_SMBDEFAULT) == (I2C_SR2_SMBDEFAULT));
}
/**
* @brief Indicate the status of General call address reception (Slave mode).
* @note RESET: No Generall call address
* SET: General call address received.
* @note This status is cleared by hardware after a STOP condition or repeated START condition.
* @rmtoll SR2 GENCALL LL_I2C_IsActiveFlag_GENCALL
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_GENCALL(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR2, I2C_SR2_GENCALL) == (I2C_SR2_GENCALL));
}
/**
* @brief Indicate the status of Master/Slave flag.
* @note RESET: Slave Mode.
* SET: Master Mode.
* @rmtoll SR2 MSL LL_I2C_IsActiveFlag_MSL
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_MSL(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->SR2, I2C_SR2_MSL) == (I2C_SR2_MSL));
}
/**
* @brief Clear Address Matched flag.
* @note Clearing this flag is done by a read access to the I2Cx_SR1
* register followed by a read access to the I2Cx_SR2 register.
* @rmtoll SR1 ADDR LL_I2C_ClearFlag_ADDR
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_ClearFlag_ADDR(I2C_TypeDef *I2Cx)
{
__IO uint32_t tmpreg;
tmpreg = I2Cx->SR1;
(void) tmpreg;
tmpreg = I2Cx->SR2;
(void) tmpreg;
}
/**
* @brief Clear Acknowledge failure flag.
* @rmtoll SR1 AF LL_I2C_ClearFlag_AF
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_ClearFlag_AF(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->SR1, I2C_SR1_AF);
}
/**
* @brief Clear Stop detection flag.
* @note Clearing this flag is done by a read access to the I2Cx_SR1
* register followed by a write access to I2Cx_CR1 register.
* @rmtoll SR1 STOPF LL_I2C_ClearFlag_STOP\n
* CR1 PE LL_I2C_ClearFlag_STOP
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_ClearFlag_STOP(I2C_TypeDef *I2Cx)
{
__IO uint32_t tmpreg;
tmpreg = I2Cx->SR1;
(void) tmpreg;
SET_BIT(I2Cx->CR1, I2C_CR1_PE);
}
/**
* @brief Clear Bus error flag.
* @rmtoll SR1 BERR LL_I2C_ClearFlag_BERR
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_ClearFlag_BERR(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->SR1, I2C_SR1_BERR);
}
/**
* @brief Clear Arbitration lost flag.
* @rmtoll SR1 ARLO LL_I2C_ClearFlag_ARLO
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_ClearFlag_ARLO(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->SR1, I2C_SR1_ARLO);
}
/**
* @brief Clear Overrun/Underrun flag.
* @rmtoll SR1 OVR LL_I2C_ClearFlag_OVR
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_ClearFlag_OVR(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->SR1, I2C_SR1_OVR);
}
/**
* @brief Clear SMBus PEC error flag.
* @rmtoll SR1 PECERR LL_I2C_ClearSMBusFlag_PECERR
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_ClearSMBusFlag_PECERR(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->SR1, I2C_SR1_PECERR);
}
/**
* @brief Clear SMBus Timeout detection flag.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll SR1 TIMEOUT LL_I2C_ClearSMBusFlag_TIMEOUT
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_ClearSMBusFlag_TIMEOUT(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->SR1, I2C_SR1_TIMEOUT);
}
/**
* @brief Clear SMBus Alert flag.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll SR1 SMBALERT LL_I2C_ClearSMBusFlag_ALERT
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_ClearSMBusFlag_ALERT(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->SR1, I2C_SR1_SMBALERT);
}
/**
* @}
*/
/** @defgroup I2C_LL_EF_Data_Management Data_Management
* @{
*/
/**
* @brief Enable Reset of I2C peripheral.
* @rmtoll CR1 SWRST LL_I2C_EnableReset
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableReset(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_SWRST);
}
/**
* @brief Disable Reset of I2C peripheral.
* @rmtoll CR1 SWRST LL_I2C_DisableReset
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableReset(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR1, I2C_CR1_SWRST);
}
/**
* @brief Check if the I2C peripheral is under reset state or not.
* @rmtoll CR1 SWRST LL_I2C_IsResetEnabled
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsResetEnabled(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR1, I2C_CR1_SWRST) == (I2C_CR1_SWRST));
}
/**
* @brief Prepare the generation of a ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte.
* @note Usage in Slave or Master mode.
* @rmtoll CR1 ACK LL_I2C_AcknowledgeNextData
* @param I2Cx I2C Instance.
* @param TypeAcknowledge This parameter can be one of the following values:
* @arg @ref LL_I2C_ACK
* @arg @ref LL_I2C_NACK
* @retval None
*/
__STATIC_INLINE void LL_I2C_AcknowledgeNextData(I2C_TypeDef *I2Cx, uint32_t TypeAcknowledge)
{
MODIFY_REG(I2Cx->CR1, I2C_CR1_ACK, TypeAcknowledge);
}
/**
* @brief Generate a START or RESTART condition
* @note The START bit can be set even if bus is BUSY or I2C is in slave mode.
* This action has no effect when RELOAD is set.
* @rmtoll CR1 START LL_I2C_GenerateStartCondition
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_GenerateStartCondition(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_START);
}
/**
* @brief Generate a STOP condition after the current byte transfer (master mode).
* @rmtoll CR1 STOP LL_I2C_GenerateStopCondition
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_GenerateStopCondition(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_STOP);
}
/**
* @brief Enable bit POS (master/host mode).
* @note In that case, the ACK bit controls the (N)ACK of the next byte received or the PEC bit indicates that the next byte in shift register is a PEC.
* @rmtoll CR1 POS LL_I2C_EnableBitPOS
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableBitPOS(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_POS);
}
/**
* @brief Disable bit POS (master/host mode).
* @note In that case, the ACK bit controls the (N)ACK of the current byte received or the PEC bit indicates that the current byte in shift register is a PEC.
* @rmtoll CR1 POS LL_I2C_DisableBitPOS
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableBitPOS(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR1, I2C_CR1_POS);
}
/**
* @brief Check if bit POS is enabled or disabled.
* @rmtoll CR1 POS LL_I2C_IsEnabledBitPOS
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledBitPOS(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR1, I2C_CR1_POS) == (I2C_CR1_POS));
}
/**
* @brief Indicate the value of transfer direction.
* @note RESET: Bus is in read transfer (peripheral point of view).
* SET: Bus is in write transfer (peripheral point of view).
* @rmtoll SR2 TRA LL_I2C_GetTransferDirection
* @param I2Cx I2C Instance.
* @retval Returned value can be one of the following values:
* @arg @ref LL_I2C_DIRECTION_WRITE
* @arg @ref LL_I2C_DIRECTION_READ
*/
__STATIC_INLINE uint32_t LL_I2C_GetTransferDirection(I2C_TypeDef *I2Cx)
{
return (uint32_t)(READ_BIT(I2Cx->SR2, I2C_SR2_TRA));
}
/**
* @brief Enable DMA last transfer.
* @note This action mean that next DMA EOT is the last transfer.
* @rmtoll CR2 LAST LL_I2C_EnableLastDMA
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableLastDMA(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR2, I2C_CR2_LAST);
}
/**
* @brief Disable DMA last transfer.
* @note This action mean that next DMA EOT is not the last transfer.
* @rmtoll CR2 LAST LL_I2C_DisableLastDMA
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableLastDMA(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR2, I2C_CR2_LAST);
}
/**
* @brief Check if DMA last transfer is enabled or disabled.
* @rmtoll CR2 LAST LL_I2C_IsEnabledLastDMA
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledLastDMA(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR2, I2C_CR2_LAST) == (I2C_CR2_LAST));
}
/**
* @brief Enable transfer or internal comparison of the SMBus Packet Error byte (transmission or reception mode).
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note This feature is cleared by hardware when the PEC byte is transferred or compared,
* or by a START or STOP condition, it is also cleared by software.
* @rmtoll CR1 PEC LL_I2C_EnableSMBusPECCompare
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_EnableSMBusPECCompare(I2C_TypeDef *I2Cx)
{
SET_BIT(I2Cx->CR1, I2C_CR1_PEC);
}
/**
* @brief Disable transfer or internal comparison of the SMBus Packet Error byte (transmission or reception mode).
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 PEC LL_I2C_DisableSMBusPECCompare
* @param I2Cx I2C Instance.
* @retval None
*/
__STATIC_INLINE void LL_I2C_DisableSMBusPECCompare(I2C_TypeDef *I2Cx)
{
CLEAR_BIT(I2Cx->CR1, I2C_CR1_PEC);
}
/**
* @brief Check if the SMBus Packet Error byte transfer or internal comparison is requested or not.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 PEC LL_I2C_IsEnabledSMBusPECCompare
* @param I2Cx I2C Instance.
* @retval State of bit (1 or 0).
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPECCompare(I2C_TypeDef *I2Cx)
{
return (READ_BIT(I2Cx->CR1, I2C_CR1_PEC) == (I2C_CR1_PEC));
}
/**
* @brief Get the SMBus Packet Error byte calculated.
* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll SR2 PEC LL_I2C_GetSMBusPEC
* @param I2Cx I2C Instance.
* @retval Value between Min_Data=0x00 and Max_Data=0xFF
*/
__STATIC_INLINE uint32_t LL_I2C_GetSMBusPEC(I2C_TypeDef *I2Cx)
{
return (uint32_t)(READ_BIT(I2Cx->SR2, I2C_SR2_PEC) >> I2C_SR2_PEC_Pos);
}
/**
* @brief Read Receive Data register.
* @rmtoll DR DR LL_I2C_ReceiveData8
* @param I2Cx I2C Instance.
* @retval Value between Min_Data=0x0 and Max_Data=0xFF
*/
__STATIC_INLINE uint8_t LL_I2C_ReceiveData8(I2C_TypeDef *I2Cx)
{
return (uint8_t)(READ_BIT(I2Cx->DR, I2C_DR_DR));
}
/**
* @brief Write in Transmit Data Register .
* @rmtoll DR DR LL_I2C_TransmitData8
* @param I2Cx I2C Instance.
* @param Data Value between Min_Data=0x0 and Max_Data=0xFF
* @retval None
*/
__STATIC_INLINE void LL_I2C_TransmitData8(I2C_TypeDef *I2Cx, uint8_t Data)
{
MODIFY_REG(I2Cx->DR, I2C_DR_DR, Data);
}
/**
* @}
*/
#if defined(USE_FULL_LL_DRIVER)
/** @defgroup I2C_LL_EF_Init Initialization and de-initialization functions
* @{
*/
uint32_t LL_I2C_Init(I2C_TypeDef *I2Cx, LL_I2C_InitTypeDef *I2C_InitStruct);
uint32_t LL_I2C_DeInit(I2C_TypeDef *I2Cx);
void LL_I2C_StructInit(LL_I2C_InitTypeDef *I2C_InitStruct);
/**
* @}
*/
#endif /* USE_FULL_LL_DRIVER */
/**
* @}
*/
/**
* @}
*/
#endif /* I2C1 || I2C2 */
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F1xx_LL_I2C_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|